...
Slicers:
https://www.prusa3d.com/page/prusaslicer_424/ for Prusa MK3
https://bambulab.com/en-us/download for Bambu Labs P1S
Material Selection and Configurations
We commonly print in three five materials, PLA, LW-PLA, TPU, PETG, and carbon fiber PETG (commonly called CF PETG on our team). PLA is good for low-stress and low-temperature applications, like cabin seats, and for prototyping as it is inexpensive but not particularly strong with a lower melting point than our other filaments. LW-PLA is similar to PLA but is close to half the weight, this makes it good for non-structural large competition drone parts that are a simple single extrusion. TPU is a flexible rubber-like filament, it is gett for parts that need vibration dampening, note it cannot be used in the AMS system on our Bambu Labs printer. PETG is good for applications with small loads, like a sensor mount, and/or lots of heat, like an ESC case. CF PETG should be used for any structural prints, like motor mounts, as is it quite strong and has a high melting point. If you expect many iterations to test geometry and fits, it is best to print your prototypes out of PLA or PETG as our CF PETG is more expensive.
The Prusa Slicer has a dropdown for filament, these defaults usually work well but sometimes the temperature suggestions for our filament will vary slightly.To change the filament type in
Bambu Studio:
To use Bambu Studio, follow the steps here (except for creating an account and downloading Bambu Handy): https://wiki.bambulab.com/en/x1/manual/introduction-to-bambu-studio
If you are a PM or a lead, you have access to log in to the WARG Bambu Labs account and printing remotely, if you are not a PM or lead, you can remove the mircoSD card from the printer and save your gcode there.
Notes on using Bambu Studio:
We have a Bambu Labs P1S printer with a 0.4mm nozzle and a Textured PEI Plate
If you are printing using the mircoSD: Make sure the filament you want to use is in the first slot of AMS (the filament system on the printer that can house up to 4 filaments) or, if you’re using TPU, that AMS is disconnected from the printer (clear tube on the back of the printer) and the end of the TPU roll is loaded instead.
The default filament presets tend to work quite well as most of our filament is Bambu Labs branded
You can use the auto-place feature to automatically place the part on the best face, sometimes you may wish to change this for better layer directions though
The tree supports usually work very well and are easiest to break off your print when supports are needed
When choosing infill, consider the load the part will be under. Things like electronic cases can be printed at around 10-15%, while structural parts like motor mounts should be closer to 40-50%. We should never have a reason to print at anything higher than 50%.
Prusa Slicer:
Click the filament dropdown
If you see the type of filament in the dropdown, select it
If you don’t see it, you can select Add/Remove filaments and you will be given a larger array of filaments
...
The default settings for “Kimya PETG Carbon” are a good starting point, but we recommend changing them slightly to look like this:
...
Plating Parts and Infill Selection
To add a part to the Prusa Slicer, you can either drag your STL file from your computer and drop it into Prusa, or click File>>Import>>STL and select your file from your computer.
...
If your part is flat or can all be printed straight up without any floating material you can set the supports option to none, otherwise the best option is “supports everywhere”.
Slicing and Starting the Print
When you are ready to print just click Slice Now at the bottom right, you will then see the estimated print time and a graphic showing the layers as they will be printed, including supports. If you’re happy with this, click “Export” and save it onto the printer’s SD card.
...
Keep an eye on your print for the first few layers and hit the x button on the printer if something goes wrong.
Print Troubleshooting
If the first layer isn’t sticking:
Clean the build plate with rubbing alcohol
Clean the build plate with soap and water, dry well
Clean the build plate with acetone (PEI sheets only)
Print with a raft
Print the first layer at a slower speed
Recalibrate it until the filament is coming out the correct amount and adhering to the build plate
If filament isn't extruding and/or the extruder is making a clicking noise
Check that the correct extruder temperature is set
Unload the filament, cut the end, and reload the filament
Recalibrate first layer
Check nozzle for jams by inserting needle into the end, there are needles in the red bins next to the printer
If print won't come off the print bed
Put the print bed in the freezer and wait 20 minutes, then try to remove print again
Flex the print bed
Heat the print bed again and try to remove the print
If it is still stuck, use acetone, this will ruin the print but will save the more expensive bed
Updating Firmware
You need a USB B plug to update the firmware. Look in the cable bins on the electrical shelf to find one, and follow this youtube tutorial: https://www.youtube.com/watch?v=h4IrBGgJa90