Page Comparison

Note: Stopping development of old arch for managers. Drivers to be transfer over or merged into new arch workflow.

Drivers

• Sensor Fusion - Polly Liu & Liam Suter

  • prototyping with bmx160

  • Code tested and functioning on arduino

    • Calibrating sensor today in the bay (hopefully can get gyro and accel readings in order. I still don’t fully understand how to calibrate the magnetometer though)

    • Starting code for the IMU on the STM32 in the meantime

• GPS

  • Ria Prakash assigned, but no progress

• CRSF Driver - Uzayr Hussaini

Telemetry Manager Yarema Dzulynsky

• No update: Waiting for new arch M1 to complete for porting M2 TM.

• Check if still interested to work on TM (will we have work for him for TM with how new arch is going?)

Path Manager Ayoung Eun

• Ideation code should be available in the repo now.

• If I remember correctly, we have to wait until simulation team comes up with airplane\drone’s tested data, correct? Or are they available already?

• Moving to a new task, hopefully we will port PM stuff to new arch as new arch gets to a point that allows for it

Infrastructure

Core Dump Kabir Verma

• Got the stack trace on a general project

ZP Validation Image Ethan Leung

• My cube environment seems to be broken because I’m unable to flash my code to the ZP, still don’t know how to fix (Hardy was able to flash to ZP3 using same method as me)

ZP3.5 M2 Bring-Up

• Stalled

Drivers Ethan Leung

• Message Queue Dami Peng

ESC (Jeffrey Zhen)

• Get the the full system running with the CAN ESC board!

• Completed with video, I think we’re good to close this task?

Servo

• Larry Pan Code for the Rx queue implementation is done, will move on to testing next. Rx Queue to Shorten ISR ← this is merged!

• System testing is done with a single servo driver!

• Looking for user-end documentation to be done

• The code still needs to be cleaned up

• Needs someone to facilitate the dynamic node allocation

• Hardy Yu can take one/two onsite people working on the rest of the project.

• Looking for people

• Also I (Roni Kant) need to finish CAN repo setup/arch so that things are cleaner but been busy with all the other start of term stuff, will aim for finishing it during work session this weekend

Sensor Cluster Roni Kant

• Tochi and Henry still willing to work on this, need to check with Aidan

• Henry is almost done his task, will work on it during work sessions, and would like another task to work on while he's remote during the week

LED Board Folarin Fatola (Unlicensed)

• Successfully reading and writing messages to and from the CAN bus!

  • Can parse and transmit the Ardupilot status requests

  • TODO: figure out how to get Ardupilot to transmit custom messages (ie altitude) and parse those messages into lighting commands

  • TODO: figure out if it is possible to send our own custom packets over the shared bus and get Ardupilot to ignore them

• Refactored Neopixel code into a mode cohesive C++ interface

6s Power Module Bryan Ma Harry Chen

• We read the datasheet for the battery monitoring chips and filled in some more port info on our document. There are still some concerns though, namely:

  • The REF_SEL register sets the range of our voltage and current measurements, but we don’t know what value to put into the register

  • The voltage and current information seem to be transmitted via both I²C and multiple analog pins of the IC. Is this for redundancy or is there another reason for this?

CAN Baud Rate Auto Sensing Teighan Miller Sherry Lai

• Working on configuring L5 board and building code.

• I believe it was said that Sherry is no longer able to work on it?

Tracking Antenna Omer Sajid Jeremy Zheng

• Worked on it today. Yaw works relatively well. Pitch is still being worked on. Tracking Antenna really well in the simulation though. Yaw should be ready for this weekends flight test.

• Going tomorrow again to work on it along with Jeremy Zheng and Roni Kant

• Need to check if they’re still interested/on-site

Drone Tuning

• Really good opportunity if you’re interested in joining us at comp this summer