Mech

Electrical

Capacitor analysis

Question: are we making a second pegasus?

• yes: new one will have thinner plates, be lighter

• functionally the same

• control system for 2 pegasus…. up to you @ EE EFS

Anthony Zhelnakov wants to measure inductance of the power wires. He is thinking about making a copy of existing power wires for the 2nd pegasus. Coz it makes measuring inductance easier.

Wait on this until harness is cleaned up :?:

→

Doing this capacitor analysis while harness for peggy 2 is being made, analysis is done on peggy 2 harness, not 1.

Harness for pegasus 1 & 2

• Can reduce weight and make this smaller - we want this for pegasus 2 in particular. “Plus configuration”

  • it’s no biggie if the harness on peggy 1 remains how it is

discussion brought up with reference to above section (capacitor analysis)

EFS

Wind Estimation

logs analyzed in order to find propeller drag: from Feb 3rd FT

• Anthony Luo will tell someone about this in EFS meeting

Motor control / FFT bidir dshot?

• Anthony Luo will tell someone about this in EFS meeting

Mech

Houston Sensor Mounts

• We have 1 op flow mounted on houston

• We do not have a second rangefinder (1D lidar)

  • We would need to take the 1D lidar off pegasus in order to fly it on houston.

The next time we fly autonomous OA with terrain following, we will want the rangefinder on houston - within next 3 weeks mount complete

+ do not need lidar on peggy at the moment

Electrical

Houston Sensor Harnessing

Lot of extra wires on houston at the moment, starting to interfere with compass

put some time towards new houston harness, good opportunity to learn/teach during potentially an EE work session

things like crimping wires/ anything we need to replicate for pegasus we should try out on houston first!

Rangefinder harness needs to be made too (see above mech section)

EFS

Houston Sensor Calibration

All was prepped for the 10th Flight test; maybe needs some looking, because of strange control behavior near end of the flight test? to be discussed - note from Megan Spee

• matek opflow working from Andy Meng experience?

Houston has large twitches to lean angle. could be caused by OA, sensor glitch, GPS issue, loose mounting, etc. old sensors may work better? See above point for Andy Meng experience

perhaps houston was not using the optical flow last flight test…. examine further to make sure houston is getting the data it needs

Autonomy

Mechanical

Mounting

VTX mount may need to be done again.

Depends if we change VTX location/item based on interference! 😄

Monster mount exists. nice

Electrical

VTX harnessing

Neel Patel Neel Patel built harness for this. This new VTX harness needs to be labeled.
we should raise antenna handling awareness RF Devices (to be written during reading week)

we need to order pre-crimped jst wires and build harness with proper connectors

when testing VTX, make sure there is an antenna!

general antennas

Antenna mounting locations.

• some antennas may need particular connectors or lengths that will be difficult to source

• gemini for example, cable maybe not easily extended…

• LTE/VTX/GEMINI antennas places so they don’t interfere with each other.

  • as far away from each other as possible

EFS

RC Controller Mapping

standard template to be created at some point Anthony Luo

• to understand logical switches, etc

Ardupilot Mux Output Config

“Really easy to do” (true)

For next flight test latest

Ardupilot OSD Config

Jerry Tian and Neel Patel helped with building the harness connecting the vtx , OSD and FPV Camera. Tested the OSD overlay on a video receiver, and it is working, could see the telemetry data when Pegasus flew. 🔥

Need more investigation and testing on the intermittent disappearance and reappearance of the overlay, also need to include more FPV cameras and a mux in the harness for completion. - Ayush Ganguly

Autonomy

LTE Video?

Possible / ready to FT early march?

to be discussed next meeting!

script written thurs, tested friday. Issues with libraries. getting logging script ready for next flight test

Mech

Gemini case?

“can be done but not urgent” - last meeting

Electrical

RFD Board

ready to bringup. Yuchen Lin

ELRS Gemini PCB

Still missing power connector gg. Somehow they still haven’t arrive, blame aliexpress

CASE:

Gemini Enclosure Requirements

Fan is optional

Case can be done this weekend, but is not required

Diversity Gemini RX board

• Forgive my ignorance I am new to RF and all of this

• My main question: How do I do component selection for the chip? Does it depend on what’s on Farris’s Gemini Board, the frequencies, or something else?

• This may be less of an AEAC question and more of an EE question…

EFS

Gemini LinkStats

• Gemini linkstats not being passed through to TX16? (Only relay linkstats)

  • Assigned to Owen Grimm

ally Improved Streaming

• See Long Range Streaming by qqqlab · Pull Request #2113 · ExpressLRS/ExpressLRS · GitHub

  • Assigned to Aryan Kashem, but no update

• ELRS Airport is unable to give sufficient datarate for some of our ground station uses in it’s current state

• Not sure if this will be comp ready. either this, or buying for xbees for the tracking antenna - Anthony Luo

Tracking antenna only needs position message? Nathan Green

Anything special when forwarding it (to 2 different recievers - ZP and tracking ant?) not sure if able to send to both, maybe need different packages?

• usb to laptop to filter packages down to position

• instead of fwd’ing from MP have groundside pretend to be another device and only request position.

• either way need arduino on groundside.

• does filtering need to be done on droneside? (@Xierumeng) no, only needs groundside. could probably build this into ELRS (built it into the radio) - Anthony Luo

to follow up with auto/efs - Anthony Luo

• cool if someone can work on stripping out all message except position.

  • from transmission side.

  • output over USB of JUST position. Nathan Green

Autonomy

LTE

• LTE has been switched from Zerotier to a Mavlink forwarding server hosted on oracle cloud with a public IP. 🚫

• GCS failsafe works now when any part of the link disconnects

• LTE disconnects when flying at high speed.

  • This could be due to the antenna angle changing as the drone tilts, interference in the cell signal or USB cable caused by higher electrical noise when at higher throttle, or something else entirely.

  • It reconnects when the drone slows back down.

• I (Nathan Green ) added an extension cable to one of the antennas and mounted it on a landing leg to see if that improves the signal. It keeps the antenna away from sources of noise on the top of the drone and the plates won’t block it when angled.

  • Will test this next flight test.

• Autonomy needs to make a script that logs LTE signal strength https://www.waveshare.net/w/upload/6/68/SIM7500_SIM7600_Series_AT_Command_Manual_V2.00.pdf (AT+CSQ) and operator (AT+COPS?) to a file for next flight test. This will help determine if it is an interferance issue, roaming issue, or something else. The modem could be trying to roam on another network and failing, and it would have to be forced to stay on one.

  • talked to Maxwell Lou

  • would be nice to have “..to a file for next flight test. “ feb 10

script would run locally on Pi, log the commands from the modem to a text file.

Reach out to autonomy leads / in autonomy meeting about this. Megan Spee

python script → output in serial →

Mech

Pegasus

Houston

Houston landing gear request via Anthony Luo from jan 29

• couple times houston tips over when it lands

• requesting landing capability while in ‘slight translational motion’

Estimated 300 g additional weight max for new landing gear

https://discord.com/channels/776618956638388305/824066661820399697/1206579554274119680

Electrical

LED Board

Board is brought up. We are having problems flashing code to the MCU. See EFS Section below

Sensor harnessing

Need appropriately sized wiring looms(?) for the sensors.

Potentially crimping own wires? Colour standards? Sheaths? etc…

Power Harnessing

Smaler / lighter weight battery harness to be made. +4 configuration only. Current wire lengths are significantly longer than necessary.

Houston Harnessing

pls clean this up ! Lots of compass interference issues & extra weight that we don’t want to be carrying

EFS

LED Board Firmware

• Owen Grimm tried flashing the firmware to the microcontroller after the board assembly. They encountered some obstacle on flashing, and I think they will try the high voltage programming later because this is what written in the data sheet the proper way to do flashing

Autonomy

Mech

Tracking Antenna Mechanical

On track. Need to 3D print. Bearings and Gears received. Still waiting on ServoCity parts.

Electrical

Nucleo Shield

• Nolan Haines Michael Botros Please update this document with status and your questions (they can be answered async, ik u guys have work lol)

• Current status

  • Schematic done, board layout is close to being done.

  • There will be some changes to the overall board to make it smaller and more compact.

  • Currently rewriting all the documentation for the board for readability.

• Questions:

Check mechanical’s documentation on tracking antenna before proceeding!

If questions are not answered please Check arch doc/ offline submit to mechanical

• I basically wanna make sure tracking antenna PCB can support all of our ground station towers, is there a link or place with a list or block diagram of our different towers?

• Will tracking antenna have enough and all the proper connectors to support different peripherals on the tower?

• Currently for VTX tower, tracking antenna only supplies 12V power, is this all thats needed from tracking antenna or is more connectivity needed?

check again asynch - Anthony Luo will look, wait until tomorrow 10 am approx

EFS

Arduino Tracking Antenna

• Lost ELRS receiver, RP. Another procurement coming next week.

• Failed ground test due to code failure. Problem occurs while waiting for satellite fixes. Will solve this issue this week.

Autonomy

Pilots/GSO’s - please submit interest in the link found in #announcements

Doesn’t guarantee spot @ comp - but we are looking for members that are able to commit to going to comp earlier rather than later.

Need at least 2 - ideally 1 pilot 1 gso, but will consider 2 of either if necessary.

All interested team members will be given access to ground school - only 2 members will be sponsored.

Fix 360 lidar

EFS or Auto to take a look