Helios M2 System Tracking Doc

Helios M2 System Tracking Doc

Task Description

Mission

  • fixed wing composite aircraft

  • Future VTOL conversion should remain possible

  • Easy to manufacture with WARG composites capability

System Architecture Diagram

Helios_M2.drawio.png

 

Master Calculations Doc

https://uofwaterloo-my.sharepoint.com/:x:/g/personal/r2vasa_uwaterloo_ca/IQA-j3FmiNiiSrTaqAXYUy-jAcBcTWKNwfGoc-GAkuEZc8s?e=dniqgA

  • please use this sheet only for system level calculations other peoples design will be determined by

  • run major changes by leads and PMs

Constraints

Constraints

Written By

Value

Constraints

Written By

Value

MTOW

Rohaan Vasa

7 kg

Empty Weight (including batteries)

Rohaan Vasa

5kg (max 5.5kg)

Payload

Rohaan Vasa

1.5-2kg

Endurance Target

Rohaan Vasa

45 mins (with reduced batt for M2) (Design for M3 batt but fly M2 with smaller pack)

Cruise Speed

Rohaan Vasa

20 m/s

Stall Speed

Rohaan Vasa

10 m/s

Max head wind for testing

Rohaan Vasa

8m/s

Max demonstrated xwind for testing

Rohaan Vasa

5m/s

Take off and land method

Rohaan Vasa

Off runway for both (no hand launch)

Landing Gear Type

Rohaan Vasa

Tricycle landing gear, Fixed MLG and NLG (steerable NLG)

Geometry Constraints

Constraints

Written By

Value

Constraints

Written By

Value

Wing Span

Rohaan Vasa

2.5m

Aspect Ratio

Rohaan Vasa

6.25

Chord Length

Rohaan Vasa

0.4m

Wing Area

Rohaan Vasa

1m^2

Wing Loading

Rohaan Vasa

96.4 N/m^2

Fuselage length

 

 

Tail Moment Arm

 

 

Prop Diameter Limit (for M3 pusher prop) drives span of Hstab

 

 

Fuselage height above ground (landing gear height)

Rohaan Vasa

Enough to allow for 16in prop mounted on rear bulkhead

Boom Seperation

 

  • min 20in apart (10in from center) to avoid prop

  • Most likely wider than that to allow for stable quad flight

 

Performance and Power Constraints

Constraints

Written By

Value

Constraints

Written By

Value

Cruise Power Needed

Rohaan Vasa

450 W

Cruise Thrust

Rohaan Vasa

11N

Climb Power

Rohaan Vasa

300W

Total elec power during climb

Rohaan Vasa

800W

Motor Max Power

Rohaan Vasa

1.25kW continous

Prop Diameter

Rohaan Vasa

16in

Structural Frame Sizing: Wings: Starting Assumptions Parameter Value MTOW 10 kg (for m3) (maybe 11-11.5kg) Weight, (W) (10kg * 9.81 = 98.1 N) Air density 1.225 kg/m³ Target stall speed, (V_s) 11 m/s Estimated CL max 1.3 Target aspect ratio 6.25 Wing Area Wing Loading Wing Span and Chord Reynolds Number Powertrain sizing: Battery Sizing: Using the Molicel P42A 21700 cells: capacity 4.2ah max discharge current: 45A mass - 65g Constraints: must be made as 2 6s packs because of charging reasons must use these cells as we have 400 of them 12s to lower current during transition for M3 as we will be using a lot Battery Architecture The proposed battery consists of two 6S4P modules connected in series: Forward Pack: 6S4P Rear Pack: 6S4P Combined Configuration: 12S4P Cell Count Total Cell Count = 48 cells Nominal Voltage V_{nom}=43.2V Fully Charged Voltage V_{max}=50.4V Pack Capacity = 16.8 Ah Pack Energy = 726 Wh useable = 581 Wh (80%) Current Capability Each cell is capable of 45 A continuous discharge. Four cells in parallel: I_max = 4 × 45 = 180 A Battery Mass Estimate Cell Mass Mass_cells = 48 × 65 g Mass_cells = 3.12 kg Estimated Pack Mass Including: Bus bars Wiring Connectors Printed casing Estimated completed battery mass: Mass_pack ≈ 3.3–3.6 kg Endurance Estimate Cruise Condition Assumed cruise electrical power: P_cruise = 500 W Flight endurance: t = 581 / 500 t ≈ 70 min Higher Power Condition Assumed average electrical power: P = 700 W t = 581 / 700 t = 0.83 hr t ≈ 50 min

 

Configuration

  • High wing

  • Twin boom

  • Bronco style tail

  • Propulsion

    • single pusher

    • add 4 quad motors for M3

  • removable empennage for transport

 

Initial Mass Budget (very rough, can change as we go through design)

Component

Mass (g)

Component

Mass (g)

Battery Pack

3500

Rear pusher motor

480

ESC

150

Propeller assembly

120

Wings

800

Fuselage

600

Tail booms

300

HStab

150

VTails

300 (total)

Landing Gear

250

Servos and linkages

200

Avionics

250

Fasteners, adhesive, inserts, misc

300

Total Empty Weight (Including Battery):

3.50 + 0.48 + 0.15 + 0.12 + 0.80 + 0.60 + 0.30 + 0.15 + 0.10 + 0.25 + 0.20 + 0.25 + 0.30

= 7.20 kg

Manufacturing Methods and Materials

Airfoils:

  • HStab can be foam core wrapped in 2 plys of 3k carbon

    • one layer of 0-90

    • one layer of +-45

  • V-Tails can be split molded with either sandwich panel or printed ribs

  • Wings can be split molded with ribs, spars and shear webs made of sandwich panels that are routered to shape

Mounts:

  • optimized light weight printed cases for electronics

Rules of thumb:

  • Avoid heavy foam + paper + epoxy mistake from M1

  • Use printed nylon / CF-nylon parts where reasonable

  • Minimize aluminum except high-load inserts, motor mounts, landing gear, or hardpoints

 

Avionics Hardware

  • ZP4 Flight Controller (has IMU & Baro onboard)

  • 1x EP Dual

  • 1x SiK Telem Radio v3

  • 2x Micro M10 GPS

  • PMO2D

  • Rangefinder

Assignee

Assignee

Asana Task

Date

Assignee

Asana Task

Date

 

 

 

 

Sub-Pages

 

Task Progression/Updates

Author: Rohaan Vasa : May 31st 2026

Initial Concept Drawings (no need to follow this 100% pls come up with your own ideas if they are better)

Wings:

image-20260531-231235.png
87936CBD-61AD-4475-99A5-ECBEBA2A3BD1_1_105_c-20260310-021056.jpeg

Inspiration for wing skeleton

image-20260531-232848.png
image-20260531-232906.png

 

VTails:

image-20260531-233712.png

Inspo for tails

image-20260531-233744.png

Fuselage:

image-20260601-005353.png
Inspo for fuselage and CW
image-20260601-010608.png
image-20260601-011734.png

aim for this type internal structure

 

image-20260601-011614.png