Task 2 Egg/Dropping Idea - Double Claw

Task 2 Egg/Dropping Idea - Double Claw

Note: Everyone contributing to this doc should have already carefully read through CONOPS, found here: https://www.aerialevolution.ca/wp-content/uploads/2026/09/2027-AEAC-CONOPS-v1.0-2026-09-08.pdf

Specifically, make sure you are familiar with the task two description, and the mark breakdown.

See pages 23-26 of the CONOPS, under section 5.2.4

Big Project

Project

Project Manager

Big Project

Project

Project Manager

Valkyrie

Comp 2027

Jackson Barber

Jackson Barber I can try to write these in within the next week, if you can fill them out yourselves that would be great

Constraints

Written By

Append Date

Constraints

Written By

Append Date

 Claw does not obstruct/ contact landing gear

 Raunak Snowden

 Sep 30, 2026

 Claw is capable of containing a chicken egg and multiple <= 3cm diameter spheres

 Raunak Snowden

 Sep 30, 2026

Claw has a grabbing area of 250 mm+

  Raunak Snowden

 Oct 31, 2026

 Claw should be lightweight as to not weigh down the drone excessively, should be < 0.75kg

  Raunak Snowden

 Oct 31, 2026

 Servos used for claw ramp pivots must exert Torque > 0.04 N*m

  Raunak Snowden

 Oct 31, 2026

 

 

 

Task Description

Task 2 is split into 2 main mechanical tasks, tagging and sample collection.

Tagging: We will create a custom tracker that can either be attached to the prop animal using a hook and loop fastener, or dropped in a nearby box for less points.

Sample Collection: We will look for and attempt to pick up 3 different kinds of samples

image-20260916-133013.png

After picking these up we will drop them off in a designated location

Task Progression/Updates

Author: Raunak Snowden person updating Date: Sep 30, 2026

image-20260930-223835.png

Updates from October 1, 2026 meeting

  • Have one big scooper under Valkyrie.

  • Have a cylinder drop down on one of the claws that can be used to collect dung.

  • Have some way to tilt the claws back after closing, and have some notch to store the items in. Then have a way to reset it so it can be repeated.

  • Have some mechansim for closing the claws (like lead screw, or something else that allows them to tilt up more easily).

Updates from October 5, 2026 meeting

  • Going to try and get a 300x300 mm grab area with claw

  • Overall mechanism will be about 530x300 mm

    • 50 mm long claws, 65 mm long and 65 mm high collection area

    • Total height not including TPU arms will be about 150 mm

  • Aiming for a dung sample 2 cm in diameter and 10 cm long

    • This is what shape of tube should be

    • Square on opposite end to push dung in can be about 30x30 mm

  • Have walls at front and back to prevent objects from falling out the side while being collected

  • In the collection area make sure there’s space enough for ~3 eggs and ~10 droppings

    • Can make each slot in the collection area about the size of one egg

  • For dung collection, use cylinder on one end, and block on the other

  • Dung cylinder and block will be mirrored and move back and forth concurrently

  • Distance from claw on bottom to dung collecting cylinder can be about 80 mm to leave room for claws to tilt up while carrying egg without interfering with the dung collecting mechanism when it’s not in use.

  • Need to look into worm gear/rack method for actuating dung collection mechanism

    • image-20261007-000834.png
  • If we’re using a DC motor with encoder we need some way to zero it (push button at the top or something)

  • Need to spec out motor to use for the lead screw

  • Need to figure out mechanism for tilting up claws to drop our items into the collection area

    • Can use drawstring (with continuous servo maybe?)

Initial Rough CAD:

image-20261028-204530.png
Sketch of the design concept
Roughdungpushergif.gif
“Spatula” mechanism to push dung into cylinder
Roughclawgif.gif
Claw moving with the Spatula

Current List of Parts:

  1. 93625A223: https://www.mcmaster.com/93625A223/

  2. 91290A115: https://www.mcmaster.com/91290A115/

  3. 7549K16, Precision Flange Nut: https://www.mcmaster.com/7549K16/

  4. 91290A166, Black-Oxide Alloy Steel Socket (the name is cut off, probably a socket head screw): https://www.mcmaster.com/91290A166/

  5. 90576A212, Medium-Strength Steel Nut (the name is cut off, probably a hex nut): https://www.mcmaster.com/90576A212/

  6. 7549K73, Lead Screw: https://www.mcmaster.com/7549K73/

  7. 8978K932, Rigid Aluminum Tubing: https://www.mcmaster.com/8978K932/ (+- 6 thou) https://www.mcmaster.com/89965K491-89965K492/?utm_term=aluminum+tubing&matchtype=e&campaignid=22729975174&adgroupid=182181498192&location=9001027&gad_source=1&gad_campaignid=22729975174&gbraid=0AAAAACLR9bzULpDXKEX_R3R4ARYkVy3w7&gclid=CjwKCAiAhqHXBhAXEiwATbksU-XsWj-Aq5Ip-DhOlP6URV70NjozRQoDoRtG6T_ArLySdivLMuymghoCdwQQAvD_BwE

  8. Couplers: amazon.ca/MECCANIXITY-Flexible-Couplings-Aluminum-Connector/dp/B0GFCMZZS7/ref=sr_1_20?crid=3C5OQ520BKT1V&dib=eyJ2IjoiMSJ9.LcakUuL0G4Ez0B5WusZuFEU8jHLOISa8Isv7uaWLMiCTt238GIsY3qcE6wF_oEkPbb2aLk9jUG7O6CNgrodGWoNkCF1SQD_Km-aYvTTdLl7dVZOue4x8D3C8M6GhGwDOCkHLPDTMIvHpAca7ZOMwJFVL1YzLYhQAhti0BpBOcCIG2o7B3G5bWcckfFGhYID3R2-fo9XvMPOmdASdLPCV-zgwOXnBK5BhjRYBsSRdOR6CTQlqWByOOsemCDL7zmt9oYo64QmV248JhaYPHV95dMEhGieLYozngfysSjG5iA4.raWMbpfzGg53h0qdEFVKQ9RaBrbPwUG2p9AZu0-Y0fY&dib_tag=se&keywords=5+x+10+mm+clamping+shaft+coupler&qid=1793927187&sprefix=5+x+10+mm+clamping+shaft+coupler%2Caps%2C142&sr=8-20

  9. polymer bushing https://www.mcmaster.com/2706T25/

November 5, 2026 Meeting

  • Bond fixed claw to tubing, no flange nut necessary

  • For landing gear should be stable, made of TPU, more than 1.2mmx1.2mm (same thickness as landing gear) use washers to mount the

  • Make flipper flush with ground by adding flat end, make it shorter

  • Find existing flange nuts

  • Use clamping coupler from amazon

  • insert nema into CAD

  • IGUS, Mcmaster carr for polymer bushing https://www.mcmaster.com/2706T26/

  • heat set insert

  • 3d print thin, or wooden skewer for one way doors, low friction

  • switch to 12 guage 5052 Aluminum

  • Make BOM

November 10, 2026 Meeting

  • Remove flange from fixed end

  • Fillet TPU part

  • Can make PETG frame mount thinner (5mm)

  • Make frame->TPU connector shorter to minimize material

  • Remember to use washers for frame connection to 3DP part when assembling

  • Reduce each frame connection to 4 screws

  • Use wireframe to align hole

  • Hole to access screw for attaching servo horn to servo gear

  • Find some padding for lining the inside of storage containers

  • Cut down lead screw and aluminum guide rails

  • Bolt M3s through the aluminum guide rails for mount to frame

  • Move screws securing flange closer to flange so it secures it more reliably. Reduce securing screws per flange from 4 to 2.

  • Swap servo mount to use 2 part epoxy to bond to the bottom aluminum sheet of the claw (can sand down a PETG print to get good bond)

image-20261111-010128.png

 

image-20261111-012413.png

 

  • Can go down to 2 screws on the tabs here