Meeting Scope

Track state of new Cornflakes airframe post previous flight test
Identify and update deliverables, owners for each subteam for flight test next weekend
Look into long-term flight test planning (general flow of what we would like to ideally test)

Other Concerns

Cutoff for when we can’t run competition frame at competition
- Only need one test to validate the frame, cool to take risk from PIC perspective (Anthony)
- Very little odds that we’ll use this frame again in next comp cycle - more likely to damage electronics on Cornflakes than Icarus
- Only use Cornflakes if Icarus is crashed extremely badly before comp (can’t be fixed)
- Fly it at least once before comp

Date	Note
April 2nd	Continuation of March 18th flight test: Fixed Wing Validation Continue rest of the tests “RTL” - set to QRTL (Return in Quad Mode only) We tested this on Houston and it worked last flight test “CS1” Data collection How much energy required to land/take-off, fly a certain distance, etc. Get a much better idea on aircraft characterization as a whole Houston: Get Houston ready VTX with 5.8 GHz (unless 1.3 GHz transmitters is received) Houston will carry second battery FPV Validation with VTX Run VTX Range test (with car, with drone, etc.) auto-land precision How close to target can Ardupilot land given the waypoint, whether CV will be required fixed wing flight battery drain Estimating based on the health of the current battery to extrapolate to new/healthier batteries guided flight mode Try different fixed-wing modes to determine what is more/less relevant Test series of waypoint-following by drone
April 8th	Icarus Frame first flight (reach goal) Quad mode testing - UP and DOWN Basic roll, pitch, yaw characterization and control Progressively move towards transition and fixed-wing validation If not, then CS2 with “Cornflakes”
April 16th	Hold for: Icarus CS2 Test out QR code based upload of waypoints re Task 1 Plan out full path for waypoints Aidan Bowers (Deactivated) (SysInt’s already made comp-sim plan)
April 22nd	Continue tasks from CS2
April 29th	1 week before comp - full systems check

Subteam	Tasks (replace these w/asana links when you can)	Owner
Mechanical (Frame)	Fix Tail Section: Fix Cabin on Cornflakes: Lengthen landing gear (switch to 16” prop, add more landing gear clearance): Add velcro for better fastening of lid:	Alison Thompson
Electrical	Attach new servo: https://app.asana.com/0/1203349931374647/1204140734762158 Identify if new servos need to be purchased if no old ones exist	Nolan Haines
Sysint	End-to-end functionality test: https://app.asana.com/0/1203349931374647/1204140737238144 : Aidan Bowers (Deactivated) RC Link with antenna Control surfaces work (all servos) Motors run the right direction GPS, IMU works Calibration of compass, accelerometer Prepare Houston for Flight: Ethan Abraham Verify all motor directions, RC Link, etc. Fix pitch directions, etc. Mount + wire VTX Add second battery for VTX	Aidan Bowers (Deactivated) Hamza Ali
Logistics	Logistics ensure vehicles, submit FTR, verify bookings. Submit flight test plan Vehicle logistics Ensure checklists are being followed Fill flight box	Hardy Yu

Subteam	Tasks (replace these w/asana links when you can)	Owner
Mechanical	ICARUS frame Ready	Conall Kingshott
Electrical	Icarus Wired	Nolan Haines
Sysint	Video Receive Tower Ready Details in arch doc Yuchen Lin	Aidan Bowers (Deactivated) Hamza Ali
Logistics	Logistics ensure vehicles, submit FTR, verify bookings. Submit flight test plan Vehicle logistics Ensure checklists are being followed Fill flight box	Hardy Yu

Component

Tasks (replace these w/asana links when you can)

Owner

Mechanical

Update re latest date for readiness:

Electrical

Updates:

State of Icarus wiring diagram - Complete by 2-April-2023
Questions on power architecture and other follow-up from RFC re last week
Information: 2023 System Architecture
Develop system block diagram
Top-down physical electronics layout
SMEs:
- Anthony Luo
- Nolan Haines
Rayyan:
- Working on identifying and listing all components/devices required in Power Architecture Power Architecture Devices/Components List
- Working with Farris Matar to categorize all components/devices and find their needed power consumption values Power Distribution Architecture
- Next steps would be to continue working with Farris on Power Distribution Architecture and contacting any other members to ensure accurate work.
Michael:
- Added components from system architecture document to drawio schematic, started connecting new components in schematic
- Next steps involve reaching out to team members for more detailed information to connect the rest of the components.