Page Comparison

Background

I’m working on itHalf of this is out of date

Reasoning Behind Restructuring

We are once again restructuring path manager! The current goal is to restructure PM so that it focuses more on path management while AM will take care of movement such as calculating roll, pitch, yaw, and adjusting throttle.

State Machine Changes

Some state names have been renamed to better reflect what is happening within the state. resetVariables has been renamed to FlightStageSelectorMode where PM will figure out what stage of flight needs to be executed.

The coordinateTurnElevation state has been removed as it previously calculated roll, pitch, yaw, etc which has been passed onto AM. Now, the desired heading is calculated in one of the flight modes and is passed to AM to make movement calculations.

Main Structure of PM

A diagram of the general flow of Path Manager, including its modes, stages, and states can be found below.

PM has been sectioned into to main modes: CommsWithStateManagerMode CommsWithSystemManagerMode, and FlightStageSelectorMode. Within CommsWithStateManagerMode CommsWithSystemManagerMode, PM will get the relevant instructions and information from AM, TM, and Sensor Fusion. This retrieval process is separated into three stages CommsWithAMStage, CommsWithTMStage, CommsWithSFStage where PM will get information from both managers and sensor fusion respectively. Note: these may be The stages originally created to get information from AM, TM, and SF have been combined into one stage depending on how State Manager sends us the informationwithin CommsWithSystemManagerMode.

PM will then check if the drone is under manual control by receiving a WaypointType . If it is not under manual control, it will enter FlightStageSelectorMode, the main part of the state machine. Within this mode, PM will change flight states if triggered to do so. While flying, PM may enter any of the following flight states: Disarmed, Takeoff, Cruising, Landing, and Landed. Note: a Preflight state and PreflightStage stage may be added. If we are in the Disarmed state or Landed state PM will go back to the start. However, if we are in Takeoff, Cruising, or Landing, PM will execute their respective stages.

...

Important Structs

Note: These All messages to Path Manager will all be coming from State System Manager in a single packet:

SM → PM

...

Code Block

typedef struct CommandsFromSM CommandsForAM_t{ WaypointType waypoint_type; // heading unit vector and magnitude float heading_dist_x;CommandsFromTM telemetry_commands; floatJetsonToZpMovementCommand headingjetson_dist_y; float heading_dist_z;commands; floatLandingInitiationCommand headinglanding_magnitudeinitiation; // Magnitude distance to waypoint target double velocity_target; // Target velocity of drone approaching target } CommandsForAM;

AM → PM Struct:

AM will send to PM an armed flag to signal that we are ready to fly. Additional information TBD

typedef struct CommandsFromAM{
    bool armed;  
} CommandsFromAM;

TM → PM Struct:

LosSFData sf_data;
} CommandsFromSM;

and CV will be sending a list of waypoints during Cruise and Search (sent through TM and SM) where a single waypoint is defined in the TelemWaypointData struct below. The start_landing flag will be signaled when a landing pad is found.

CV/TM → PM During Cruising

struct TelemWaypointData GpsCoordinates{    
  double longitude;  //    
  double lattiude;   
  uint8_t waypoint_id; 
};

typedef struct TelemWaypointData CommandsFromTM{
    uint8_t  struct GpsCoordinates gps_coords; num_waypoints; // number of waypoints in the list 
    intTelemWaypointData waypoint_idwaypoints[num_waypoints]; 
} CommandsFromTM;

CV/TM → PM During Search For Landing Pad

// Data given from CV/TM during search and typedeflanding 
struct JetsonToZpMovementCommand CommandsFroTM{
   {
  float x;
  float y;
  float z;
  float heading;
};

struct LandingInitiationCommand {
    bool start_landing; 
};

PM → AM Struct:

typedef struct CommandsForAM_t{
  int num_waypointsfloat dist_forward; //pitch
  float dist_right; // roll
  float dist_up; //yaw
  float magnitude; // number of waypoints in the list 
    TelemWaypointData waypoints[num_waypoints]; 
} CommandsFromTM;
 Magnitude distance to waypoint target
  float heading; // heading at target waypoint
  double velocity_target; // Target velocity of drone approaching target
} CommandsForAM;