Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 7 Next »

Change Description

Icarus

System Electrical Routing Guidelines

Daniel Puratich

daniel.puratich@uwaterloo.ca

Description of Change

Add the below section to the arch doc:

System Level Electrical Placement & Routing Guidelines/Information:

  • The frame should not be electrically connected (aka should be at floating potential)

    • Complies with: UL1740

    • This can be checked with a DMM (when the system is not powered)

    • This means that if a PCB we are using has electrically connected mounting holes we need to take proper steps to achieve isolation

      • Sometimes PCB mounting holes are electrically connected to a GND plane for thermal reasons so we should also approach thermals with caution on sensitive electronics

  • Conformal Coating can be used within reason

    • The pro of conformal coating is waterproofing and makes it harder to accidentally should with a screw driver

    • The con of conformal coating is it prevents heat from leaving a PCBA

      • So anything that is conformal coated should receive a thin layer at most

    • Another con is that it can be annoying to remove in the case of reworking a PCBA

    • For example it would be fine to conformal coat a flight controller that runs cool

    • However, for example an RF transmitter we would want to approach with more caution

      • We could place a large heatsink on the primary chip(s) using thermal paste

      • Then we could consider conformal coating the other portions of the board

  • Cables, especially longer cables, should be within sheaths when reasonable

    • This offers protection against abrasion during natural flight vibrations

    • Exception to this rule is shorter cables that are placed further from anything that could be abrasive, specifically cables purely within the avionic compartment of our aircraft

  • Avoid loops in cable runs if possible

  • Varying conductor types should be separated when reasonable

    • Generally we consider four different types of cables: Digital, Analog, Power, & Coax/Rf

      • Digital: Characterized by signals with fast edges

        • Fast edges refers to low microsecond rising/falling edge range and faster

          • Clarify rise/fall time (offer examples of rise/fall times we’d expect on our system)

        • Generally transcieving in 0 and 1 states asynchronously or synchronously

        • I.E. a GPS module’s cable connection to our flight controller is digital

        • An IMU is an example of a particular digital device that is sensitive to external noise.

      • Analog: Characterized by signals with slow edges

        • Slow edges refers to high microsecond rising/falling edge range and slower

          • Clarify rise/fall time (offer examples of rise/fall times we’d expect on our system)

        • Generally transcieving data in varying voltage states

          • Though some protocols we consider analog will also transmit some digital data as well

        • I.E. a hobby fpv analog video camera has an analog data output

        • An analog video feed out of an analog camera is an example of a particular digital device that is sensitive to external noise.

      • Power: Characterized by constant voltage varying current designed for power transmission

        • Generally the voltage is constant though higher frequency noise may be present

        • These conductors can have significant current pulses

        • I.E. a connection from a battery to an ESC

      • Coax/Rf: Characterized by oscillating signals across the spectrum (~20kHz to ~300Ghz) intended for wireless transmissions and notably contained within a coaxial cable

        • A coaxial cable, specifically for our applications utilizing an SMA or RP-SMA connector, is generally used to guide sensitive RF signals between transceivers & antennas.

          • It is also worth noting antenna placement is critical, this is noted below in more detail

          • SMA & RP-SMA connector info should be found in the corresponding connectors arch doc section.

        • Because coaxial cables offer strong noise immunity the routing constraints of these cables are looser than others

    • Each of these type of conductors should be physically grouped together, however, each type should be separated

      • I.E. All power stuff near each other, all digital near each other, but power separated from digital

      • This grouping and separation is physical distance, though of course there are other factors

      • Within PCBAs these groups may be mixed, this is fine, we will assume the PCB designer has taken the proper care to avoid issues as necessary

  • RF Transceiver Care

    • An RF transmitter should not be turned on (given input power) without a proper antenna connected as this can permanently damage the transmitter

      • Possible violations of this policy should be reported in Discord and transmitters should be labelled as damage (notably degraded performance) may not be immediately evident. We don’t want to blame each other, stuff happens, we just want to note it for the future! If you do not feel comfortable stating this publicly feel free to DM a lead you’re comfortable speaking to who can relay the message without naming names.

    • Transmitters generally get warm

      • They require a lot of power and therefore require some cooling

      • They are sometimes designed to be mounted outside an airframe for ambient cooling of wind passing the frame. As we may not be doing this we need to approach this with caution.

      • Notes regarding conformal coating are above.

    • The lower the frequency the longer the distance we can get for the same output power generally

    • The higher the frequency means more bandwidth generally

  • Antenna mounting

    • GPS sensors in particular are to our 900 MHz and 1.3 GHz transceivers and should be mounted away from antennas operating at these frequency ranges

    • Radio waves do not like to change medium

      • Specifically they do not like to pass through materials of varying dielectric constant

        • Passing waves through some varying materials may be fine, but be careful!

        • At the frequencies WARG operates at (6 GHz and below) foam will not have a considerable impact on signal integrity

      • This means mounting antennas outside of cases/airframes and providing LOS when reasonable

    • Antenna polarity should be deliberate

      • Antennas that use diversity should be mounted not in the same plane

      • Antenna polarity matching follows the below graphic

  • (Antenna Mounting Continued)

    • Ground antenna should be mounted with as much distance away from the ground as possible

      • This is to reduce ground reflection and has a considerable effect on reliability of an RF link

    • Antenna spacing should be minded

      • Any device with diversity (multiple antenna inputs) should have it’s antennas mounted with some spacing between them. Always follow manufacturer guidance here.

        • IE our VN-300 has specific manufacturer recommendations regarding recommended spacings and clearances

      • Different devices should have their antennas spaced out

        • See notes about frequencies and channels above.

Implementation

We will discuss in RFC channel. This is just documenting knowledge for newer members to understand.

Reason for Change

Assist in Mech Elec integration

Priority

Medium

Impact of Not Responding to Change

Confusion

What Groups, People, Sub-teams Need to be Notified?


Change Impact

Additional Parts/Resources Required and Costs

None

Impact on deadlines

Minimal

Alternatives and Recommendations

NA

Comments

I would appreciate verification and input on some of what I’ve written here. See Discord thread.



Change Request Sign Off -

Status

✅ Accepted / ⏸️ On Hold / ❌ Rejected / (question) More info Requested

Comments

Signatures/Name

  • No labels