Mech

Electrical

New ELRS Hardware Project

• Nolan Haines please do some research and put questions here to be addressed during the meeting, this meeting is a great time for integration discussions like this!

  • TABLED

6S ESC motor selection

• Rayyan Mahmood 2023-2024 Motor Comparison Table

U

6S comp drone motors not up to date…

this is something that can be used on houston (3S)

EFS

Wind Estimation

• Ardupilot feature to be enabled

logs analyzed in order to find propeller drag

Weathervaning?

• Potential feature to be tested.

Mech

Houston Sensor Mounts

Electrical

Houston Sensor Harnessing

• ^ see above.

Optical Flow (OFS)

Rangefinders (Sonar/Lidar/Radar)

EFS

Houston Sensor Calibration

Specifically for houston

see if the issues with tuning pegasus are replicated on houston

~~ probably a few days before feb 10

Autonomy

Mechanical

Mounting

VTX mount to be reviewed, forwards-facing camera mount ready to be printed.

• printer small difficulty, print in RPC or something

feb 10!

Electrical

VTX harnessing

EFS

RC Controller Mapping

Ardupilot Mux Output Config

Ardupilot OSD Config

• Confer with pilots on preferences.

Autonomy

LTE Video?

Possible / ready to FT early march?

Mech

Electrical

RFD Board

• order still shipping, ETA next week

EFS

Gemini LinkStats

• Gemini linkstats not being passed through to TX16? (Only relay linkstats)

Improved Streaming

• See Long Range Streaming by qqqlab · Pull Request #2113 · ExpressLRS/ExpressLRS · GitHub

• ELRS Airport is unable to give sufficient datarate for some of our ground station uses in it’s current state.

Autonomy

LTE

• LTE has been switched from Zerotier to a Mavlink forwarding server hosted on oracle cloud with a public IP.

• GCS failsafe works now when any part of the link disconnects

• LTE disconnects when flying at high speed. This could be due to the antenna angle changing as the drone tilts, interferance in the cell signal or USB cable caused by higher electrical noise when at higher throttle, or something else entirely. It reconnects when the drone slows back down.

• I (Nathan Green ) added an extension cable to one of the antennas and mounted it on a landing leg to see if that improves the signal. It keeps the antenna away from sources of noise on the top of the drone and the plates won’t block it when angled. Will test this next flight test.

• Autonomy needs to make a script that logs LTE signal strength https://www.waveshare.net/w/upload/6/68/SIM7500_SIM7600_Series_AT_Command_Manual_V2.00.pdf (AT+CSQ) and operator (AT+COPS?) to a file for next flight test. This will help determine if it is an interferance issue, roaming issue, or something else. The modem could be trying to roam on another network and failing, and it would have to be forced to stay on one.

Mech

Pegasus

Cabin is constructed and mounted on the drone, flew and tuned with it on Saturday.

Houston

Houston is out of commission mechanically atm, houston tests need to be on hold until the landing gear and lidar mount are replaced - Alison Thompson

• maybe by feb 10 we have a new and improved lidar mount

Houston landing gear request via Anthony Luo

• couple times houston tips over when it lands

• requesting landing capability while in ‘slight translational motion’

Limited on weight. In short-term, current version can be remade. Can get someone on adding more support.

• what flight weight does houston need to stay under?

  • Megan Spee Anthony Luo to find an answer (or do this properly) 😞

  • either test this IRL or just pick a nice number

Electrical

LED Board

• Parker Lawrence-Valeriani EFS handoff procedure?

• Anything I can do to make the handoff easier?

EFS

LEB Board Firmware

• Owen Grimm first the first prototype code for LED board

• Waiting for leads to do the PR

• Waiting for the chips to arrive to do bench test

Autonomy

Mech

Tracking Antenna Mechanical

Parts have been ordered. Sheet metal has been cut and bent. Plan is to build one first and then build the other. On track.

Electrical

Nucleo Shield

• Nolan Haines Michael Botros Please update this document with status and your questions (they can be answered async, ik u guys have work lol)

• Current status

  • Schematic done, board layout is close to being done.

  • There will be some changes to the overall board to make it smaller and more compact.

  • Currently rewriting all the documentation for the board for readability.

• Questions:

Check mechanical’s documentation on tracking antenna before proceeding!

If questions are not answered please Check arch doc/ offline submit to mechanical

• I basically wanna make sure tracking antenna PCB can support all of our ground station towers, is there a link or place with a list or block diagram of our different towers?

• Will tracking antenna have enough and all the proper connectors to support different peripherals on the tower?

• Currently for VTX tower, tracking antenna only supplies 12V power, is this all thats needed from tracking antenna or is more connectivity needed?

EFS

Arduino Tracking Antenna

• Ayoung Eun Aryan Kashem did the ground test on Sunday I think

• “The tracking antenna follows the altitude, failed to follow longitude and laititude

• Action task : fix the starting angle so it isn’t getting predetermined and test latitude and longitude“

Will probably complete ground testing this week and implement in flight test for feb 10. Not a huge rush but can speed up this timeline if people are interested in doing the work early.

looking for whether or not the data rate is good enough to keep the antenna pointed at the drone. So can gather this data without actually putting it on the flight line.

Budgeting: pick the lowest price point you can get away with

You need to receive corrections data from the RTK thing and send it to the GPS…

get higher quality/newer M8/9/10s or GPS in general

Autonomy

FIND PILOT (especially if on-stream in the summer )

• will sponsor advanced rpas test (once) + ground school

thx for listen