3D Printing Guidelines and Bambu Labs + Prusa Instructions

Owned by Brielle Chenier
Last updated: 2024-09-09 by Alison Thompson
6 min read

Slicers:

Material Selection and Configurations

We commonly print in five materials, PLA, LW-PLA, TPU, PETG, and carbon fiber PETG (commonly called CF PETG on our team). PLA is good for low-stress and low-temperature applications, like cabin seats, and for prototyping as it is inexpensive but not particularly strong with a lower melting point than our other filaments. LW-PLA is similar to PLA but is close to half the weight, this makes it good for non-structural large competition drone parts that are a simple single extrusion. TPU is a flexible rubber-like filament, it is gett for parts that need vibration dampening, note it cannot be used in the AMS system on our Bambu Labs printer. PETG is good for applications with small loads, like a sensor mount, and/or lots of heat, like an ESC case. CF PETG should be used for any structural prints, like motor mounts, as is it quite strong and has a high melting point. If you expect many iterations to test geometry and fits, it is best to print your prototypes out of PLA or PETG as our CF PETG is more expensive.

The Prusa Slicer has a dropdown for filament, these defaults usually work well but sometimes the temperature suggestions for our filament will vary slightly.

Bambu Studio:

To use Bambu Studio, follow the steps here (except for creating an account and downloading Bambu Handy): https://wiki.bambulab.com/en/x1/manual/introduction-to-bambu-studio

If you are a PM or a lead, you have access to log in to the WARG Bambu Labs account and printing remotely, if you are not a PM or lead, you can remove the mircoSD card from the printer and save your gcode there or, you can print remotely using the WARG bay desktop.

Notes on using Bambu Studio:

  • We have a Bambu Labs P1S printer with a 0.4mm nozzle and a Textured PEI Plate

  • Do not apply glue to the print bed! Though this is common for lots of printers, the bed we have for the Bambu Labs does not require glue and applying glue will ruin it.

  • If you are printing using the mircoSD: Make sure the filament you want to use is in the first slot of AMS (the filament system on the printer that can house up to 4 filaments) or, if you’re using TPU, that AMS is disconnected from the printer (clear tube on the back of the printer) and the end of the TPU roll is loaded instead.

  • The default filament presets tend to work quite well as most of our filament is Bambu Labs branded

  • You can use the auto-place feature to automatically place the part on the best face, sometimes you may wish to change this for better layer directions though

  • The tree supports usually work very well and are easiest to break off your print when supports are needed

  • When choosing infill, consider the load the part will be under. Things like electronic cases can be printed at around 10-15%, while structural parts like motor mounts should be closer to 40-50%. We should never have a reason to print at anything higher than 50%.

Prusa Slicer:

  1. Click the filament dropdown

  2. If you see the type of filament in the dropdown, select it

  3. If you don’t see it, you can select Add/Remove filaments and you will be given a larger array of filaments

You can view/edit the temperature settings for the selected filament by clicking the gear next to the filament dropdown, it is good practice to check this against the temperature specs on the filament roll.

If you are printing with PLA:

The default settings for “Generic PLA” are usually good, just double-check the specific roll if you haven’t used it before.

If you are printing with PETG:

The default settings for “Generic PETG” are a good starting point, but we have had better success with a hotter nozzle on the first layer and a cooler one on the rest. You may want to modify these to look more like this:

It is best to check these temperatures against those on the filament roll if you haven’t used it before.

If you are printing in CF PETG:

The default settings for “Kimya PETG Carbon” are a good starting point, but we recommend changing them slightly to look like this:

Plating Parts and Infill Selection

To add a part to the Prusa Slicer, you can either drag your STL file from your computer and drop it into Prusa, or click File>>Import>>STL and select your file from your computer.

Next, you will want to click on the part and select the “place on face” option:

When you choose what face to place it on, consider if there is a good surface to print up from, if there are any curves that need to be accurate (any holes/circles not printed from the bottom up will not be perfectly round), and what direction the load on the part will be coming from. You will likely want to ensure that the layers are perpendicular to the main force being applied to the part, this prevents your print from shearing apart.

To print multiple parts, you can drag/insert more parts into the slicer, place them on the appropriate face, and hit the icon that looks like a grid at the top of the screen to auto-arrange them.

When choosing infill, consider the load the part will be under. Things like electronic cases can be printed at around 10-15%, while structural parts like motor mounts should be closer to 40-60%. We should never have a reason to print at anything higher than 60%.

If your part is flat or can all be printed straight up without any floating material you can set the supports option to none, otherwise the best option is “supports everywhere”.

Slicing and Starting the Print

When you are ready to print just click Slice Now at the bottom right, you will then see the estimated print time and a graphic showing the layers as they will be printed, including supports. If you’re happy with this, click “Export” and save it onto the printer’s SD card.

Once your print is on the SD card, put it back in the printer, choose “Print from SD” and your part from the list.

Keep an eye on your print for the first few layers and hit the x button on the printer if something goes wrong.

Print Troubleshooting

  • If the first layer isn’t sticking:

    • Clean the build plate with rubbing alcohol

    • Clean the build plate with soap and water, dry well

    • Clean the build plate with acetone (PEI sheets only)

    • Print with a raft

    • Print the first layer at a slower speed

    • Recalibrate it until the filament is coming out the correct amount and adhering to the build plate

  • If filament isn't extruding and/or the extruder is making a clicking noise

    • Check that the correct extruder temperature is set

    • Unload the filament, cut the end, and reload the filament

    • Recalibrate first layer

    • Check nozzle for jams by inserting needle into the end, there are needles in the red bins next to the printer

  • If print won't come off the print bed

    • Put the print bed in the freezer and wait 20 minutes, then try to remove print again

    • Flex the print bed

    • Heat the print bed again and try to remove the print

    • If it is still stuck, use acetone, this will ruin the print but will save the more expensive bed

Updating Firmware

You need a USB B plug to update the firmware. Look in the cable bins on the electrical shelf to find one, and follow this youtube tutorial: https://www.youtube.com/watch?v=h4IrBGgJa90